BUYER GUIDE / HINGED ENTRANCE DOORS
Front door handing
and swing.
How to approve the opening direction before your door goes into production.
By Asvnt-Door · Published
BEFORE YOU APPROVE
Approve the movement.
Not just the initials.
On a hinged entrance door, handing describes how the door is arranged; swing tells you whether it opens into the building or out toward the exterior. To order confidently, give the supplier a plan marked exterior and interior, a hinge position, and an arrow showing where the leaf goes. If it is a double door, label the leaf you want to use every day.
Use the supplier’s handing code only after they have matched it to your drawing. A closed front elevation, like the reference shown here, cannot establish the direction of travel.
This guide covers hinged doors, not offset-pivot arrangements. For an offset axis, see the pivot-versus-hinged door guide. The photograph is a design reference; it does not confirm hinges, locks or other supplied hardware.
01 / PICK ONE VIEWPOINT
Show where
you are standing.
For a single leaf, mark the hinge edge as seen by someone standing outside and facing the closed door. Draw the same opening from above and mark the swing arc. An inswing moves toward the interior; an outswing moves toward the exterior. Write the direction as a sentence on the plan as well as an arrow. For example: Viewed from outside, hinges on the left; leaf swings inward into the hall.
For a villa entrance, put the drawing beside the site plan and walk the route from the porch to the hall. Check the handle and leaf against the return wall, nearby step, furniture and adjacent door. Ask your installer to check using finished floor levels and the proposed stop position. The fact that the leaf fits the frame does not mean it can open to the angle you need.
MMI DOOR’s handing reference shows separate diagrams for different entrance configurations. Use your own supplier’s diagram for the order; do not transfer a code or dimensions from another product chart.
02 / DESIGN FOR EVERYDAY USE
Which leaf
opens first?
For a pair, the active leaf is the one you open first for normal passage. Mark it on both the exterior elevation and plan. State whether the second leaf is fixed or opens when extra passage is needed. These are different configurations: two panels in an elevation do not establish that both are operable.
Ask the supplier to show the lock on the active leaf and what it engages when the second leaf is closed. If the second leaf is operable, confirm its release and closing sequence. Compare the usable passage with only the active leaf open against what you need day to day, rather than assuming the full width of the pair is normally available.
Imperial USA’s chart illustrates how a supplier identifies the active leaf and swing on a pair. Loewen’s technical drawings show examples where the companion panel is fixed. These are references, not Asvnt-Door hardware or specifications.
03 / COMPARE THE DOCUMENTS
One opening.
Three records that agree.
| Record | Look for |
|---|---|
| Floor plan | Exterior and interior labels, the hinge edge and the arc relative to nearby walls and steps. |
| Exterior elevation | The same hinge side from the stated viewpoint, handle and lock locations, and the active leaf on a pair. |
| Order and hardware schedule | The matching opening ID and drawing revision, swing written in words, supplier handing code and the intended operating sequence. |
04 / RECORD THE DECISION
Resolve the mismatch.
Then approve one revision.
Suppose the plan shows the everyday leaf on the right from outside, but the elevation marks it on the left. Do not assume the elevation is merely mirrored. Ask the supplier to label both views, redraw the active leaf and swing, and align the hardware schedule. Then have the project team check the corrected revision before releasing the order.
Example approval note: E-01, revision C. Viewed from the exterior, the right leaf opens first and swings inward. The left leaf stays closed in normal use and is operable for wider access. Confirm lock engagement, release sequence and clear passage with the right leaf open. This is a sample wording, not a default configuration.
If the site team has not agreed on swing, levels or passage, record the point as unresolved instead of asking production to assume. The project team should confirm any applicable access, egress or other local requirements before approval.
BUYER QUESTIONS
Two details
worth asking about.
Can I identify handing from an exterior photograph?
Not reliably. A closed photograph may suggest the handle position, but it does not show the swing arc, which leaf is active, or whether the second panel opens. Ask for a labelled plan and elevation.
Can I decide the swing after the frame has been made?
Do not assume it can be changed. Ask the supplier to assess the actual frame, hinges, lock preparation and threshold arrangement. Get an updated drawing and quote before authorising any change.
PREPARE YOUR ENQUIRY
Bring a marked plan.
Make the swing clear.
Send your opening reference, project location, the exterior viewpoint, and a swing sketch. For a pair, state which leaf you want to use every day and whether the other must open.
Discuss your entrance doorEN-02 is a starting point for an enquiry, not confirmation of a configuration or site fit.

